| Type | Standard | Model for Sensor Communications Unit *1 |
|||
|---|---|---|---|---|---|
| NPN output | E3X-HD11 | E3X-HD6 | E3X-HD14 | E3X-HD0 | |
| PNP output | E3X-HD41 | E3X-HD8 | E3X-HD44 | ||
| Connecting method | Pre-wired | Wire-saving Connector *2 |
M8 connector |
Communications Unit connector |
|
| Light source (wavelength) | Red, 4-element LED (625 nm) | ||||
| Power supply voltage | 12 to 24 VDC ±10%, ripple (P-P) 10% max. | Supplied from the connector through the Sensor Communications Unit |
|||
| Power consump tion |
Normal mode | 720 mW max. (Current consumption: 30 mA max. at 24 VDC, 60 mA max. at 12 VDC) |
|||
| Eco ON | 530 mW max. (Current consumption: 22 mA max. at 24 VDC, 44 mA max. at 12 VDC) |
||||
| Eco LO | 640 mW max. (Current consumption: 26 mA max. at 24 VDC, 53 mA max.at 12 VDC) |
– | |||
| Control output | Load power supply voltage: 26.4 VDC max., open- collector output Load current: Groups of 1 to 3 Amplifier Units: 100mA max., Groups of 4 to 16 Amplifier Units: 20mA max. Residual voltage: At load current of less than 10 mA: 1 V max., At load current of 10 to 100 mA: 2 V max. OFF current: 0.1 mA max. |
– | |||
| Protection circuits | Power supply reverse polarity protection, output short-circuit protection and output reverse polarity protection |
Power supply reverse polarity protection and output short- circuit protection |
|||
| Response time |
Super-high-speed mode (SHS) *3 |
NPN outputs: Operate or reset: 50 μs PNP outputs: Operate or reset: 55 μs |
– | ||
| High-speed Mode (HS) |
Operate or reset: 250 μs (default setting) | ||||
| Standard Mode (STND) |
Operate or reset: 1 ms | ||||
| Giga-power Mode (GIGA) |
Operate or reset: 16 ms | ||||
| Maximum connectable Units | 16 units | with E3X-CRT: 16 units with E3X-ECT: 30 units |
|||
| Mutual interference prevention |
Possible for up to 10 units (optical communications sync) *3 | ||||
| Auto power control (APC) | Always ON | ||||
| Other functions | Power tuning, differential detection, DPC, timer (OFF-delay, ON-delay, or one-shot), zero reset, resetting settings, and Eco mode |
||||
| Ambient illumination (Receiver side) |
Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max. | ||||
| Ambient temperature range | OOperating: Groups of 1 to 2 Amplifiers: -25 to 55°C, Groups of 3 to 10 Amplifiers: -25 to 50°C, Groups of 11 to 16 Amplifiers: -25 to 45°C Storage: -30 to 70°C (with no icing or condensation) |
Operating: Groups of 1 to 2 Amplifiers: 0 to 55°C, Groups of 3 to 10 Amplifiers: 0 to 50°C, Groups of 11 to 16 Amplifiers: 0 to 45°C, Groups of 17 to 30 Amplifiers: 0 to 40°C Storage: -30 to 70°C (with no icing or condensation) |
|||
| Ambient humidity range | Operating and storage: 35% to 85% (with no condensation) | ||||
| Insulation resistance | 20 MΩ min. (at 500 VDC) | ||||
| Dielectric strength | 1,000 VAC at 50/60 Hz for 1 minute | ||||
| Vibration resistance (destruction) |
10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
10 to 150 Hz with a 0.7-mm double amplitude for 80 minutes each in X, Y, and Z directions |
|||
| Shock resistance (destruction) |
500 m/s2 for 3 times each in X, Y, and Z directions |
150 m/s2 for 3 times each in X, Y, and Z directions |
|||
| Degree of protection | IEC 60529 IP50 (with Protective Cover attached) |
– | |||
| Weight (packed state/unit only) |
Approx. 105 g/ Approx. 65 g |
Approx. 60 g/ Approx. 20 g |
Approx. 70 g/ Approx. 25 g |
Approx. 65 g/Approx. 25 g | |
| Materials | Case | Polycarbonate (PC) | Heat-resistant ABS (connector: PBT) |
||
| Cover | Polycarbonate (PC) | ||||
| Cable | PVC | – | |||
| Accessories | Instruction Manual | ||||
E3X-HD11
Liên hệ
In Stock
Surprisingly Stable Detection with Your Finger tip. Exceptionally easy operation and stabilizing technology reduce maintenance cost.
Sản phẩm này đã có trong list!
Xem list sp yêu thích
Đánh giá
Chưa có đánh giá nào.